Sandvik CJ Series Jaw Crusher Part Jaw Plate
Primary Material :High Manganese Steel (Mn13, Mn18, Mn18Cr2, Mn22Cr2)
Manufacturing Process :Sand Casting with Heat Treatment
Hardness Range :HRC 50-64 (Varies by Material Grade)
Compatible Crusher Models :CJ411/JM1108, CJ412/JM1208, CJ612/JM1211, CJ613, CJ615, CJ815
Quality Standards :Metallographic Testing, Chemical Composition Analysis, Hardness Inspection
库存 11 件
PRODUCT
Description
Sandvik CJ Series Jaw Plates – Mn18Cr2 Heavy-Duty Wear Parts
The Jaw Plate (Fixed and Swing) is the primary crushing interface of the Sandvik CJ Series jaw crusher.
Engineered to crush the hardest ores and granite, these plates must withstand extreme compressive loads without fracturing.
Unlike standard market castings, our crusher spares are manufactured from modified Mn18Cr2 Austenitic Manganese Steel, designed to balance high impact toughness with exceptional abrasion resistance.
As a specialized crusher parts supplier, we provide OEM-interchangeable plates for the full CJ range (CJ411 to CJ815).
Our manufacturing process utilizes Water Toughening Treatment to ensure the microstructure is fully austenitic, preventing premature cracking under load.
Core Engineering Advantages
We address the two most common failure modes of jaw plates: plastic deformation (spreading) and cracking.
- Optimized Metallurgy (ASTM A128 Grade C): We utilize Mn18Cr2 alloy.
Compared to standard Mn13, the addition of Chromium (Cr 2%) and higher Manganese content enhances the Work-Hardening capability.
The surface hardness increases from ~220 HB to >500 HB under impact, while the core remains ductile to absorb shock. - Precision Machining: The back surface (mounting face) is CNC machined to ensure a flatness tolerance of <0.2mm.
This precise fit against the jawstock and frame prevents the plate from “rocking” and cracking during crushing cycles. - Reversible Design: Our plates feature a symmetrical tooth profile.
This allows the operator to “flip” the jaw plate 180 degrees when the bottom zone is worn, effectively doubling the service life of the wear parts.
Technical Specifications
Our replacement plates meet the strict dimensional and metallurgical standards required for Sandvik CJ series machines.
| Technical Parameter | Specification Details |
|---|---|
| Material Standard | ASTM A128 Grade C (Mn18Cr2) / Grade E (Mn22Cr2) |
| Initial Hardness | 200 – 230 HB (Ductile State for Installation) |
| Work-Hardened Hardness | 500 – 550 HB (Operational State approx. 50-55 HRC) |
| Yield Strength | ≥ 350 MPa |
| Impact Toughness | ≥ 140 J/cm² (Charpy U-Notch) |
| Compatible Models | CJ411 (JM1108), CJ412 (JM1208), CJ612 (JM1211), CJ613, CJ615, CJ815 |
| Tooth Profiles | Standard, Heavy Duty, Wide Tooth, Corrugated |
Performance Comparison
Field data from copper mine applications demonstrates the efficiency of Mn18Cr2 over standard alloys:
- Wear Life: 30% increase in service life compared to generic Mn13 plates in hard granite applications.
- Crushing Efficiency: The optimized tooth profile maintains the “Nip Angle” longer, preventing rock slippage and reducing power consumption by up to 10%.
- Reduced Maintenance: Less frequent change-outs mean lower labor costs and higher crusher availability.
Expert Maintenance Diagnosis: When to Replace?
Visual Inspection Guide:
- The “50% Rule”: When the tooth profile is worn down by 50% of its original height, crushing efficiency drops significantly as the material is pulverized rather than cleaved. Replace to save energy.
- Rotation Strategy: Do not wait until the plate is worn through.
Rotate (flip) the jaw plate when the bottom 30% of the tooth profile is worn flat. This maximizes material utilization. - Back Plate Inspection: If the back of the jaw plate shows shiny, polished spots, the plate is loose. Re-tighten the wedge bolts immediately to prevent the plate from snapping.
Expert Installation Note
Secure the Wedge Assembly: Sandvik CJ crushers use a wedge retention system.
Critical Step: After installing new plates and running the crusher for 4-8 hours (break-in), you MUST re-tighten the wedge bolts.
Manganese steel undergoes slight plastic deformation (settling) under initial load. Failing to re-tighten causes the plates to loosen and damage the jawstock face.
Maximize your primary crushing tonnage. Contact our engineering team to identify the correct tooth profile and material grade for your Sandvik CJ crusher.
“Authoritative Engineering Data: All critical metallurgical specifications and dimensional tolerances (e.g., ±0.05mm) are strictly governed by the master English documentation. While localized versions are provided for operational reference, the English original remains the sole binding authority for quality inspection and technical compliance.”





